Environment Pollution Caused By Construction Activities Environmental Sciences Essay

Environment Pollution Caused By Construction Activities Environmental Sciences Essay This chapter present the brief information and effects of the environmental issues happened in the Malaysian Construction Sites. This is a literature chapter review on the environmental pollution happened which caused by the construction activities in Malaysia. For example, air pollution, water pollution, water pollution, noise pollution, wastage problem, ground movements and etc. 2.2 Environment Pollution Caused by Construction Activities According to Krishnan Ganesh (2005) describe that the pollution consists of any change of the environment in physical, chemical or biological characteristics which might be endanger the human life and other life being. Besides, pollution might occurred in increasing of carbon dioxide (CO2) and other green house gases conversely decreasing in stratospheric ozone on global scale enhanced the global environmental pollution to air, water and land resources, biological diversity and human health. Based on Jennifer Gray (2010), the construction industry is a major source of pollution compound around 4% of particulate emissions, higher occurrences of water pollution incidents than any other industry and frequent complains of noise every year. However, the main areas of concern are including air, water, noise and soil pollution. Meanwhile, Zhen et al (2006) stated the dirt, harmful gases, noises, blazing lights, solid and liquid wastes, ground movements, messy, fallen item, and etc that hazards from construction site are the sources of pollution. It would also interrupt the residents near the area furthermore influence their health quality and well-being of people in the whole city. In short, construction industry at site has full of danger, difficult and dirty or even death syndrome which are to be encountered and control under certain rules regulations. However, these rules regulation of environmental protection can be imposed by the local statutory, government, and any other independent institutions. 2.2.1 Air Pollution Nancy J. Sell (1945) notes the definition of air pollution is an addition to our atmosphere of any materials having a damaging effect on life and environment. Normally are carbon dioxide (CO2), carbon monoxide (CO), nitrous oxides (NO), sulphur oxides (SO) and various hydrocarbons and particulates which are small particles consists of solids. The construction activities such as land clearing, operation of diesel engines, demolition, burning and working with toxic materials will contribute to air pollution. All construction activities produce high level of dust which can effects large distance over long time (Jennifer Gray, 2010). In addition, Jennifer (2010) also stated that diesel is the most critical emissions of a lot of toxic gases. Air pollution occur when the noxious vapours and other hazardous chemicals that are widely used on construction sites. The human health will be affected same as to the animal by the various types of pollutants. Most of the time, animal death can be happened by air pollutant as long it goes into the animal food sources. Damage on plant might be visible or which affect the growth, productivity and life will possess of the plants will be damaged (Nancy J. Sell, 1945). At last, the air pollution is directly linked to the human and other wild life being. This is because the poisonous air particular will damaging the respiratory systems of every living organism. Other serious diseases will also happen due to the insufficient inhaled of clean air and excessive inhaled of hazard oxygen. Therefore, the air quality is required to be controlled on construction sites moreover off the sites. 2.2.2 Water Pollution Diesel and oil, paint, solvents, cleaners and other harmful chemicals; and construction debris and dirt can be direct sources causing of water pollution. Soil erosion cause silt-bearing run-off and sediment pollution when the land is cleared. Silt and soil that run into natural waterways turn them turbid and restrict sunlight filtration and devastate aquatic life. In addition, other pollutants such as diesel and oil, toxic chemicals, and building materials from the site will be carried by the run-off of surface water. This happened to poison the water life when these substances get into waterways and any animal intake it. The source of human drinking water can be contaminated when the pollutants on construction sites soak into the groundwater which makes it much more difficult to purify than the surface water (Jennifer Gray, 2010). Based on Chiew Mynn, Jason and Joanthan (1997) shown that an example which the construction of a new golf course near the waterfall at Frasers Hill, Pahang tourism attraction. The forest nearby has been cleared, no roots to hold on to the surrounding soil and erode when the rains come. Silt and sand that comes from the construction become extremely murky and dirty as the soils run into the waterfall. Consequently, the overwhelming of construction activities surround the waterfall has lost its attraction. In short, water pollution can be affecting the health and safety of human and other wild life being gradually by intake the poisoned water sources which could not be purify completely. However, it might also cause massive damage to the building structures through the hidden running off of soil and water gradually under the foundation. Serious soil sedimentation and erosion will happen if excessive deforestation and development without proper plantation on the construction sites. Hence, the water pollution must be preventing effectively in order to provide safe and health living of building environmental. 2.2.3 Noise Pollution Noise is an increasingly omnipresent, yet underestimated, form of pollution. Long periods of exposure to relatively low levels of noise can have adverse effects on human health, such as raised blood pressure, hypertension, disrupted sleep and cognitive development in children (Kiernan, 1997), diminished working memory span, and psychiatric disorders (Bond, 1996). The vehicles, heavy equipment and machinery on construction sites create a lot of noise. Excessive noise is annoying and distracting, possible to cause loss in hearing, high blood pressure, sleep disturbance and extreme stress. Research has proven that high noise levels disturb the natural life cycles and usable habitat of animals (Jennifer Gray, 2010). As Choong Mek Zhin (2010) notes in his articles, Construction work going on at night in Kuala Lumpur and Petaling Jaya is causing many residents to lose sleep and suffer from stress due to the constant noise from the project sites. The construction works are proceeding although on public holidays. There are various noise sources on the construction sites and which reveal various types of noise which need to be managed such as background noise, idling noise, blast noise, impact noise, rotating noise, intermittent noise, howling, screeches and squeals (Lisa M. Sabitoni, 1996). Therefore, heavy noise pollution can cause mental problem of the human. This could bring a wide linkage of damages to the residential area nearby the construction sites if the noise levels are not well managed. Table below shows the noise construction activities schedule for noise limitation. Table: Typical noisy construction activities against the permissible noise limits (Khairul Sani B Samsudin, 2007) Type of Works 7am-7pm 7pm-10pm 10pm-7am Very Noisy Works e.g. piling, blasting, demolition, concreting works, use of percussion tools e.g. pneumatic hammers, etc Yes No No Moderately Noisy Works e.g. erection/dismantling of formwork, tying/fixing of steel bars, operation of cranes, loading/unloading of construction materials, etc Yes Yes No Quiet Works e.g. housekeeping, bricklaying, plastering, painting, etc Yes Yes Yes 2.2.4 Wastage Problem Waste produced by industrial operations has to be concerned as waste levels point out the appreciation of utilize of environment natural resources while the environmental issue is in concern globally. Construction industry has contributes a major waste to the overall waste volume among other industry operations annually for majority of the country. Most of the party involved in the operation do not alert of that construction waste can happen at every stage of the activities. During the stage on construction site, most of the resources are being used, therefore the major waste level are low which it can be observed for initial stage (Teoh Su Ping et al, 2009). As Ekanayake Ofori (2000) said, Construction waste can be divided into three major categories which are material, labour and machinery waste. However, material wastage is of more concern as more of the raw materials from which construction inputs are derived come from non-renewable resources. In short, waste management stands critical step to mitigate the pollution to the environment as the construction industry has contributes a major waste to the overall waste levels among the other industry operation. This is because every construction project is unique and heterogeneous which it undergoes with many various materials, methods, machinery under such long in durations. In addition, these construction wastes can cause an excessive amount of wastages which most of the inputs are produced from non-renewable resources such as timbers, steel bars, cement and sand, clay bricks, marble and gravel tiles and etc natural resources. Therefore, waste management must be operated in order to minimize the massive wastages problems and pollute the environment. 2.3 Summary Construction industry is full of challenges among the other production industry. This is because any of the pollution such as air, water, noise, waste problems and etc can be happened in the construction sites if improper protection and prevention during every single stage of the construction. Therefore, these require lots of effort in managing the conditions of the construction sites under a long period of construction time. However, some certified Environmental Management System (EMS) with valuable process and procedure is useful in the protection of environmental quality. For example, international certified ISO 14001:2004 as an EMS. Chapter 3 Concept and Principles of ISO 14001 as Environmental Management System (EMS) 3.1 Introduction This chapter is to present the concept and principles of the ISO 14001 as an EMS in Malaysian Construction Organizations. The important information including the introduction, concepts, benefits, methods, issues, challenges of processes and procedures in terms of implementing the ISO 14001 as an EMS. 3.2 Concept of ISO 14001 ISO 14001 was first published in 1996 and specified with actual requirement for an Environmental Management System (EMS). It applies to those environmental aspects which the organisation has control and over which it can be expected to have an influence. ISO 14001 is often seen as the corner stone standard of the ISO 14000 series. However, it is not only the most well known, but is the only ISO 14000 standard against which it is currently possible to be certified by an external certification authority. Having stated this, it does not itself state specific environmental performance criteria. This standard is applicable to any organization that wishes to Implement, maintain and improve an environmental management system Assure itself of its conformance with its own stated environmental policy (those policy commitments of course must be made) Demonstrate conformance Ensure compliance with environmental laws and regulations Seek certification of its environmental management system by an external third party organization Make a self-determination of conformance (ISO 14000/ ISO 14001 Environmental Management Guide, 1996) 3.3 Implementation Process of EMS based on ISO 14001 According to Sarkis (1998), who has listed down the five important steps which showing the successful implementation process of Environmental Management Systems (EMSs) based on ISO 14001. The five important steps are shown as below: Environmental policy: Firms must capture in a written document their intentions and principles in relation to their environmental behaviour. This statement must show firms commitment to comply with environmental legislation, to prevent pollution and also to potentially improve their environmental performance. It also must be accessible for the public. Planning: Firms have to identify controllable environmental aspects and determine which ones have significant environmental impacts. These are the ones that firms should attend first. Then firms have to determine the legal dimensions of these impacts (which will depend on the sector, the geographical situationà ¢Ã¢â€š ¬Ã‚ ¦) and, based on this information, they have to establish objectives and targets as well as the EMS to achieve them. Implementation and operation: it means the allocation of human, financial and physical resources for these issues. Managers have to assign the environmental responsibilities, provide the suitable training to employees and also establish the internal and external communication channels in order to spread the environmental commitment among all the members in the organization and the stakeholders. Checking and corrective action: It includes the measurement of environmental performance, the identification of deviations by comparing targets and results and the application of corrective actions when necessary. In order to be able to carry out these activities, firms must keep environmental records and have periodical auditing of the EMSs. Management review: In order to guarantee the effectiveness and continuous improvement of the EMSs, managers have to review and get a feedback of all the policies, objectives and procedures. (Sarkis, J., 1998) At first, the organisations must comply with the environmental policies to prevent the environmental issues furthermore to improve their environmental performance. Then, the planning on controllable environmental aspects and impacts must be made in order to set up objectives and targets to be achieved by the organisations. Subsequently, experienced personnel have to apply the environmental management systems and ensure the environmental commitment has reached to every member in the organization as well as the stakeholders. Consequently, checking and corrective action must be taken which consists of environmental performance measures, comparison on divergence findings and rectifies actions. It would also required scheduled environmental records and periodical auditing of the EMS. Lastly, the management review step enables the managers to reassess and collect feedback related to the effectiveness and necessary improvement required on the policies, objectives and procedures. In short, a good EMS consists of not only the general five important steps of implementation processes but also required good integration of communication and coordination channels in between the executive personnel, managers, staffs, labours and other stakeholders. This could be the most critical point which might directly influence the effectiveness and efficiency of EMS in the entire organisations. 3.4 Benefit of Implementing ISO 14001 in Construction Organizations According to Blackmores (2008) noted, there are three (3) main categories of benefits which are financial, operational or internal and external ranges as shown below: Financial Cost savings by minimise the waste and use of natural resources such as electricity, water, gas and fuels efficiently. Identify the environmental risks and addressing the weaknesses. Helps the organisation to prevent the fines and penalties by fit to meet the environmental legislation, Indicating better risk management to helps minimising the insurance costs. Operational/Internal Improve the performance and efficiency in general Constrict the production processes, minimise in the risk of incidents and produce better efficiency Eliminate unforeseen and consistency by controlling the disruption and waste Staffs responsibility are clarified clearly Internal communications and morale improved External Express as innovative and forward thinking approach Lead to better public perception of the organization and a competitive advantage, furthermore to improve sales opportunities Lead to better community awareness of the impact of the construction activities on the local residents such as noise, smell, dust, vibration, etc. Demonstrate commitment to the environment and provide confidence to the customers, trade partners, stakeholders, regulators and local authority In addition, the implementing of ISO 14001 gives a lot of benefits such as protection of the environment; reduced operating costs; increased access to markets; demonstrated compliance with regulations; improve environmental performance; improved customer trust and satisfaction enhanced corporate image and credibility; employee involvement and education; and potential impact on world trade to allow competition on an equal basis (George Ofori et al, 2000). 3.5 Environmental Management System (EMS) Do It Yourself (D.I.Y.) Schemes by CIDB EMS DIY Schemes is a part of the effective communication plan to be jointly executed by CIDB and Stakeholders, it was designed for given the significant importance of external accreditation which encouraging the construction companies to attain the ISO 14001:2004 certification. This scheme has two certifications which are ISO 14001 EMS Certificate and the CIDB EMS Certificate. However, there are 3 main objectives which to be achieved by the CIDB as listed below: Provide formal recognition of certified contractors on commitment to excellence environmental management Convenient the employers of the contractors such as JKR, housing developers and local authorities to select certified contractors, who have practicing commitment to excellence environmental management Provide CIDB with an index for monitoring and reporting the general environmental management awareness and practice of Malaysian contractors, as reflected in the annual number of contractors certified to the two EMS certification schemes. The overall aim of these schemes is to subsidise the Malaysian contractors with a cost-effective program in order to improve their performance up to a standardised level as well as in developed countries. Meanwhile, it also helps to assist the contractors to upgrade their environmental management performance throughout the EMS certification programs. At first, the contractor has to attend the EMS Awareness Program which consists of 3 module, such as Module AP1, AP2 and AP3 in order to choose whether CIDB EMS Certification Program or ISO 14001 EMS Certification Program. This allow the contractor to understand regarding Why, How and Benefits or Implementing Systematic Environmental Management before selecting either one of the EMS Programs by CIDB. Besides, an EMS Awareness Training Certificate will be issued by the CIDB to the participant after the completion of 3 training modules in the EMS Awareness Program. After that, it is a condition precedent to carry on either one of the two EMS D.I.Y. Programs by CIDB and 3 months will be given the participants to decide after completion of EMS Awareness Program. The following table shows the EMS Awareness Program. Table: Environmental Management System Awareness Program (CIDB, 2007) Phase Period Milestones Activities Action by Man-day Support Environmental Awareness and Education 2 Months Training Module AP1 Environmental Issues Malaysia Environmental Policy Introduction to CIDB- D.I.Y Scheme. Introduction to Global Environmental Problems and Management Issues. Introduction to Malaysian environmental management policies Consultant 1 Training Module AP2 Introduction to ISO 14001 EMS Introduction to ISO 14001:2004 EMS Standard and the Requirements. Strategic EMS Implementation Plan. Consultant 1 Training Module AP3 Malaysia Environmental Legal Regulatory Requirements Awareness of the current environmental legal and regulatory requirements in the Malaysian construction industry To identify legal and other requirements and develop appropriate Legal Register Consultant 1 Total Man-day 3 3.5.1 CIDB EMS Certificate D.I.Y. Program CIDB EMS Certification Program is an EMS Program under CIDB EMS DIY Scheme which takes 6 months from Phase 1 to 4 as shown in the table below. However, the participant must undergo the EMS Awareness Program before undertake this program and it only allows the CIDB registered contractors from Class G1-G6. Conversely, Class G7 contractors are only permitted to participant for ISO 14001 EMS Certification. There are some conditions in implementation of the EMS required such as, the first year shall be for one on-going project, second year shall be for three on-going projects, third and subsequent year shall be for all projects. Meanwhile, the name of all projects involved in the implementation of EMS shall be included in the CIDB EMS certificate and annual renewal of the certificate is depend on the compliance satisfaction with the annual EMS audit requirements. The action plan of the CIDB EMS Certification Program is shown as below: Table: CIDB EMS Certification Program Processes (CIDB, 2007) Phase Period Milestones Activities Action by Man-day Support EMS Planning Documentation 2 Months Training Module CP1 EMS Plan Training to Introduce the EMS Plan (Content and Implementation Steps). Development of the EMS Plan. Consultant 2 Contractor Activity Prepare EMS Plan Contractors to prepare the EMS Plan Submit to Consultants for evaluation. Contractor Evaluation of EMS Plan 0.5 Month Module CP2 On-site Evaluation of the EMS Plan On-Site review the EMS Plan interview key staffs. Identify the EMS Implementation Project (minimum 1 construction project). Suggest improvements. Contractor 1 Contractor Activity Take Corrective Action Based on evaluation findings, contractor takes appropriate corrective action and amends the necessary documentation. Contractor Implementation of EMS Plan 2.5 Months Contractor Activity Implementing the EMS Plan Contractor implements the EMS Plan (Office and minimum 1 construction project). Contractor Module CP3/CP4/CP5 Consultancy Support on the EMS Plan Implementation Consultant will visit the contractor monthly to provide on-site implementation advices and supports. Consultant 3 CIDB Audit 1 Month Module CP6 CIDB EMS Certification Audit CIDB Appointed Auditor performs the EMS Certification Audit. CIDB Appointed Auditor 1 Contractor Activity Take Corrective Action Take corrective actions to close out the non-conformance found in the Audit. Submit corrective action plan to Auditor. Contractor Award Award of CIDB EMS Certification Certification Award after review of the corrective action plan. TOTAL MAN-DAYS 7 DAYS Registration Fee and Payment The table below states the overall registration fees to be paid. The payments are separated into 2 stages upon the start of the respective phases. Meanwhile, the registration fees need to be paid upon the Stage 1 (EMS Awareness Program). However, these payments are excluded the accommodation and travel fees of the participants. Table: CIDB EMS Certificate D.I.Y. Program Fee and Payment (CIDB, 2007) CIDB EMS Certificate D.I.Y. Program Total Fee: RM 8,500.00 Payment in 2 Stages Phases Main-Days Payment by Contractors Environmental Awareness Education 3 Stage 1 EMS Planning and Documentation Evaluation of EMS Plan 3 Stage 2 Implementation of EMS Plan CIDB Audit 3 1 It also covers the following: Award of CIDB EMS Certificate 3.5.2 ISO 14001 EMS Certificate D.I.Y. Program ISO 14001 EMS Certification Program under CIDB EMS DIY Scheme is an EMS Program by CIDB. It takes 10 months to complete from Phase 1 to 6 and it is open to every contractors. Table below shows the ISO 14001 EMS Certification Processes. Table: ISO 14001 Environmental Management System (EMS) Certification Program Phase Period Milestones Activities Action by Man-day Support EMS Appreciation 0.5 Months Training Module IP1 ISO 14001 EMS briefing for Top Management Presentation to Top Management on the EMS Objectives, Benefits, Roles and Responsibilities. Consultant 0.5 EMS Planning 2.5 Months Training Module IP2 Environmental Policy, Aspects Significant Impacts Training on methods to identify and develop Environmental Aspects Impacts. Decide Criteria and Methodology for Determining Significant Impacts. Consultant 1.5 Contractor Activity Prepare Policy, Legal Environmental Aspects Register, Implementation Plan Contractor to prepare the Environmental Policy, Legal Registers and Environmental Aspects Impacts Register. Contractor to plan develop and implementation plan and milestones. Contractor Module IP3 On-site Review Consultation on Policy, Legal Aspects Register Assessment of current EMS status against ISO 14001:2004 other legal requirements. Review the Implementation Plan Approach for the EMS implementation Consultant 2 Training Module IP 4 Objectives, Targets, KPI EMP Introduction to importance and formulation in establishing the objectives, targets, Key Performance Indication (KPI) and Environmental Management Program (EMP). Consultant 1 Contractor Activity Prepare Objectives, Targets EMP Contractor to prepare the environmental Objectives, Targets, KPI and EMP. Contractor Module IP5 On-site Review Consultation on Objectives, Targets, KPI EMP Consultant to review and finalise the Objectives, Targets, KPI and EMP established. Consultant 1 Documentation EMS Implementation 1 2.5 Months Module IP6 Off-site Preparation of EMS Manual Procedures Guidelines Off-site Preparation of Guidelines for EMS Manual Procedures specific to the contractors organisation. Consultant 1 Training Module IP7 ISO 14001 EMS Documentation Implementation Introduce and develop the EMS documentation (Manual, Procedures) and implementation programme. Softcopies provided for the Environmental System operational procedures and forms. Consultant 1 Contractor Activity EMS Documentation Implementation Contractor to prepare EMS Manual Procedures based on Consultants guidelines information provided. The template formats provided on computer disk will be used. Initiate EMS Implementation Collect the initial data. Contractor Module IP8 On-site Review Finalise the EMS Manual Procedures On-site Review Consultation on EMS Manual Procedures. Amend the documents if necessary. Consultant 1 Stage 1 Audit Documentation Audit Third Party Certification Bodys Auditor conducts Documentation Audit. Certification Body Contractor Activity Take Corrective action Based on audit findings, contractor takes appropriate corrective action and amends the necessary documentation. Contractor Documentation EMS Implementation 2 1.5 Months Contractor Activity Continue EMS implementation Continue implementing the procedures and programmes as planned e.g. Records, monitoring data, training etc. as per tasks outlined. Contractor Module IP9 On-Site Consultation on Implementation Progress On-site Monitoring Consultation on Implementation of Procedures and EMP to ensure the implementation programmes are properly in place and utilised. Consultant to provide hands on guidance. Contractor 1 Checking Management Review 2 Months Training Module IP10 ISO 14001 EMS Internal Auditor Training Conduct ISO 14001 EMS Internal Auditor Training to provide skills and knowledge on how to conduct internal audit and becoming a competent internal auditor. Consultant 2 Contractor Activity Conduct Internal Audit Take Corrective Actions Contractor to conduct internal audit to identify gaps in the systems. Auditor to prepare internal audit report and issue corrective actions request if required. Responsible personnel to take appropriate corrective actions. Contractor Module IP11 On-site Monitoring Consultation on Internal Audit and Corrective actions taken To check and review EMS Implementation progress and provide hands on guidance. To close out the Corrective Action Requests. Consultant 1 Contractor Activity Conduct Management Review Conduct Management Review to communicate and review EMS performance improvements plans. Contractor Module IP12 On-site Consultation on EMS Implementation Site Readiness On-site Monitoring Consultation on Management Review and EMP. Check site condition. Consultant 1 Contractor Activity Finalise EMS and Ensure Site Readiness Contractor to finalise EMS and ensure Site Readiness. Contractor Pre-Assessment 1 Month Module IP13 On-site Pre-Assessment Perform Pre-certification assessment to determine the conformity of the EMS implementation. Identify improvement opportunities and present pre-assessment audit

Critique and Analysis of Baumann’s Article

Within this evaluation, a critical reflection will be made based on the causes of libations and to what extent the social effects of globalization provoke ‘moral outcry, based on Bandsman's 2001 â€Å"Ann-Globs† article. From which, Bandsman's key points will be analyses and critiqued. The term globalization applies to a set of processes that appear to transform our present social condition of conventional nationality into one of globosity and reliability (Stager, 2013).Within the idea of reliability, the revolution in â€Å"consumer tastes and unabated construction of global electronic highways, all Increase the inter-dependence and Inter-connections of action economies across the globe† (Dole & Lowe, 2005, p. 4). Guldens 1 990 agrees and goes on to state that globalization is the â€Å"Intensification of world wide social relations, which link distant localities in such a way that local happenings are shaped by events occurring many miles away and vice versaâ⠂¬  (p. 64).These links can relate to the ideas of increased mobility (Robins, 2000) or flows (Beck, 2000) across national borders, of products, services, Information, communication, people and ideas (Parsons and Macmillan, 2009). Whilst Levity (1983) adds to this by claiming that due to these links. globalization Is characterized by the standardization of product or services across all markets, leaving some regions developing this standardization more rapidly than others, whilst also being the most cost effective mode of competing in these global markets.As these markets become more standardized, an increase in competitive pressure and the need to survive in the economy becomes much more apparent. Therefore it could be said that globalization is about shifting forms of unman contact, this affirmation thus implies three assertions: first, that we are slowly leaving behind the condition of modern nationality that gradually unfolded from the 18th century onwards; second, that we are moving towards the new condition of postmodern globosity; and, third, that we have not yet reached it.Globalization therefore suggests a notion of ‘development' and ‘unfolding (Stager, 2013). Such unfolding may occur quickly or slowly, but it always corresponds to the idea of change, and therefore, denotes transformation. Globalization can also be thought of s the emergence of competitive yet worldwide Interconnectedness, by the ways of flow and exchange of capital, labor and technology throughout global borders. From this, drivers of globalization appear.Drivers such as the advances in technology, the removal of political and economic barriers and the free movement of capital allow global markets to progress. Therefore, allowing such markets to become more diverse. Consequently meaning that people now have greater access to capital, technology and have less restrictive political and economic barriers. For example, due information can be created because of the innovative use of resources that are used to endorse new products and ideas across borders, regardless of geographic location.

Is a successful marriage a utopia today? Essay

The latest marriage statistics should make every couple doubt about whether their relationship shell be sealed with a marriage. Beside the fact that considerably less couples decide to marry at all, in the US every second, in Austria (as an example for middle Europe) every third marriage is divorced. This is not a particularly promising prospect for a couple planning to marry and swear to love each other for the rest of their lives. Therefore the question must be raised: Is a successful marriage Utopia today? When I take a closer look at our society, I can imagine some reasons why successful marriages, which mean staying together happily for a lifetime, have become so rare. One reason might be a shift in our society towards more self-realization and less responsibility. In my opinion many couples may not detect the enormity of their decision to marry. Before making that decision each partner should think about all consequences a marriage might have on the relationship and all consequences a marriage definitively has when it comes to legal terms. Taking the decision whether or not one wants to marry his or her partner should not be made hasty in a romantic mood or occasional feelings of perfect happiness and love. Nevertheless many couples fix their marriage either before really knowing each other or not thinking of the consequences it has. After a little time, when the butterflies in their stomachs are often gone, many couples realize that their relationship has changed, but they then have to realize as well that divorcing is by far not the same as breaking up. A second reason might have to do with the role of women in our society. Nowadays nearly every woman is educated or emancipated enough to earn her own money. Therefore only some women are still financially dependent on their husbands which was/is often a reason for women staying married although being unhappy in the relationship. A woman who earns her own money and can lead an independent life without her husband as well will have no fear of getting divorced, as this was the case in the last centuries. However, not only the roles of women, but also our society as a whole has changed and made divorce absolutely tolerable. In former times our society consisted of either happy or unhappy married couples with at least one or two children. These couples married or were forced to marry fairly early and stayed together till the end of their days. Nowadays our society is structured completely different: many couples life together without marrying or having children, others marry and get divorced once or more often. Additionally homosexual relationships are relatively tolerated and the number of singles, who spend the main part of their life alone, is one the raise too. In such a heterogeneous society divorce has become a normal, for some even a natural, thing. Terms like common law spouses have emerged and some people think of their partners as temporary phenomenon only. Nevertheless I truly believe that in the 21st century a successful marriage must not be or is not Utopia. I, for myself, cannot tell what future holds in store for me and my relationship, but I can observe many happy and therefore successful marriages which have been lasting for more than 25 years by now in my surrounding. In my opinion the society and therefore the people living in a society are always subject to change. And these changes also include changes of people’s behaviours, customs, morals or values. Although today’s marriage statistics do not suggest bright expectations for a successful marriage, I think it is still can and does happen. Maybe the preliminaries for such a marriage have changed, nevertheless many couples show us that living in our society happily and married is still possible. So, for many couples a successful marriage has become Utopia, but the alternative is still there.

The Sports Coordinator Of The Bloomington Ymca Essay

Drew Mohr Dr. Young SPH-R426 Assignment #3 Keelan Simpson (Sports Coordinator) – Monroe County YMCA, Bloomington, IN Keelan Simpson is the Sports Coordinator of the Bloomington YMCA and his main responsibilities consist of running all sports programs at the YMCA, hiring the correct employees/staff to coach or help run the different sports programs. The different sports programs include youth summer camps, youth seasonal sports, and adult basketball leagues. The YMCA is a global organization that serves all individuals of a community, allowing them to have access to recreational sports, fitness programs and many other health opportunities. What positions do you hire/allowed to hire? Volunteer seasonal coaching positions for youth sports. The biggest hires that Keelan is responsible for are the summer camp positions. Summer camp positions are important because they are employed all summer and will be working with kids the whole time. The summer camp positions are 40 hours per week, essentially full time employees. Keelan also hires outside contract work such as referees for the adult basketball league. Steps a candidate has to go through in order to get an interview/How to set up on-site interviews? Keelan and his staff typically go to career fairs and job fairs around the Bloomington area to promote the YMCA and land potential candidates. Candidates apply through an application that will be sent to Keelan from the YMCA administrative assistant. The assistant